具體的年代aw Use: 4 Hows [Starting it, Depth, Speed, Cost]

一個混凝土鋸是一個受歡迎的鋸用於切割混凝土的設備. In this article, we will see how to start different models for concretes saws. How deep they can cut, what is their cutting speed and how much does it cost to cut the concrete.

走後麵的混凝土鋸出售開始150美元

內容

如何開始混凝土鋸

開始混凝土鋸非常簡單。但是，起始步驟可能因製造商而異。讓我們看看各種品牌的啟動操作：

棉田

如果您正在進行冷啟動，請按以下步驟操作：

反複按下底漆泵，直到燃料進入它。（2）在（扼流圈）的方向上翻轉開關。（3）用一隻腳用一隻腳和管狀手柄握住後把手。
Pull the starter handle firmly until you hear the first sound of the engine starting. When the engine starts, hold down the safety lever and squeeze and release the throttle repeatedly for one or two minutes to warm up the engine. The warming up process is complete once the engine speed stabilizes and it revs smoothly from low to high speed.
Use the primer pump to start the engine when it’s warm. Place the switch in the “I” (operating) position and start the engine as described in task (3) of the procedure described earlier.

Stihl

將機器放在地麵上，砂輪不應在其旋轉範圍內有任何人。
站在一個堅定的基礎上
Press the cut-off machine firmly against the ground while also holding the handle and your thumb wrapped up around the handle.
Pull the starter grip slowly using the right hand until you find it getting harder. Then give it a brisk pull. However, be cautious to not pull the rope all the way.

Husqvarna

Slide the ignition switch to the left to start the engine.
拉出扼流圈。
按壓油門觸發鎖，然後按壓油門。接下來，鎖定油門控製（a）。放開油門。半油門控製上有一個鎖
Valve for decompression: Reduce the pressure in the cylinder by pressing the valve. This helps start the power cutter. When starting, always use the decompression valve. When the machine starts, the valve automatically returns to its original position.

Hilti.

(Once) Press the decompression valve.
底漆燈泡必須擠壓2至3次，直到它充滿燃料。
Switch the start/stop switch to the “start” position.
Choose from the following options. There are two options available. Alternative 1 / 2 Pull the choke lever upwards if the motor is cold. This engages the choke and half throttle. Alternative 2 / 2If the motor is hot, pull up the choke lever and then push it downward. This is the half throttle, so no choke is engaged.
確保切割盤可以自由旋轉。
Stand with your right foot on the lower part of the rear grip.
Pull slowly on the starter handle with your right hand until resistance is felt.
Vigorously pull the starter handle. Move the choke lever back to its original position once the motor fires for the first time (after two to five pulls of the starter).

How Deep Does A 14 Concrete Saw Cut

施工地點上最常見的天然氣鋸有12英寸的切削深度。有液壓鑽石鏈條可以切割成25英寸的深度。在截止鋸上有14英寸的圓形刀片，最大深度約為5英寸。

Due to the guide bar of a diamond chainsaw, which has a long, narrow flat surface, the saw can provide a deeper cut with no overcut, allowing the operator to make square corners. With a circular blade, this is not possible.

除了在沒有過度切割的情況下切割較深，鑽石鏈條還可用於製造小於4英寸的開口4英寸，杆的切割深度。它們對於通過材料切割奇形孔也是有用的。“

It is important to consider whether you will be cutting openings deeper than five inches when choosing a diamond chainsaw. In this case, a diamond chainsaw is a right tool. Most chainsaws start with a gas-driven two-cycle engine, which offers portability and low initial investment. Consider using a hydraulic or pneumatic diamond chainsaw, which has more power and can be used for openings up to 25 inches, if your cutting needs are significant.

How Fast Does A Concrete Saw Cut

時間值是不可估量的。因此，切割速度是為您的工作選擇鑽石刀片時的重要考慮因素。粘合的金剛石刀片是必不可少的。換句話說，如果你是切割混凝土，葉片應該輕柔地粘合，如果你切割瀝青，刀片應該幾乎不粘合。總而言之，您應該瞄準每分鍾8到10英尺的切割速度。如果您未達到此度量標準，請換新刀片。

A blade must also last for a long time. The blade needs to give you significant life even if it glides through the material. With diamond blades, most relationships are opposites. A blade lasts longer if you are cutting with lower horsepower. With a thicker rim diameter, such as a .187, your blade will cut slower but last longer.